Archive for May, 2011
« Older Entries |Rear Caliper Shim Kit
Wednesday, May 11th, 2011
Required when using Turbo rotors/calipers on early 944 setups. Includes 4 longer bolts, washers and hardened steel washers.
$19
Posted in Porsche | Comments Off on Rear Caliper Shim Kit
Boxster S Caliper adapter – 944 Rear
Wednesday, May 11th, 2011
This bracket adapts 2000-2008 Boxster S rear caliper to rear 944 arm.
The following variations are available:
-Boxster S caliper to 83-85 setup with 86T rotor
-Boxster S caliper to 83-85 setup with Boxster S rotor
-Boxster S caliper to 86 alum arm with 86 rotor
$140
Posted in Porsche | Comments Off on Boxster S Caliper adapter – 944 Rear
Boxster Caliper adapter – 944 Rear
Wednesday, May 11th, 2011
This bracket adapts 1997-2004 Boxster rear caliper to rear arm. Uses stock rotor.
The following variations are available:
-Boxster caliper to 83-85 setup with 83-85 rotor
-Boxster caliper to 86 alum arm with 86 rotor
$140
Posted in Porsche, Uncategorized | Comments Off on Boxster Caliper adapter – 944 Rear
Boxster Caliper adapter – Early 944 Front
Wednesday, May 11th, 2011
This bracket adapts 1997-2004 Boxster front caliper to 83-85 944 front spindle. The rotor has to be changed to a 84-89 Carrera. (282x24mm)
$140
Posted in Porsche, Uncategorized | Comments Off on Boxster Caliper adapter – Early 944 Front
Super beetle 944 Master cylinder adapter
Wednesday, May 11th, 2011
Precision machined from steel, this adaptor allows you mount a Porsche 944 master cylinder to your 71-79 Superbeetle. Also includes special push-rod .Proper metric grade fasteners are included.
$C54/ Kit.
Posted in Type 1/3 | Comments Off on Super beetle 944 Master cylinder adapter
955 Brakes on Dropped BJ spindle
Wednesday, May 11th, 2011
This kit adapts 955 (Cayenne) rotors and calipers to CB disk spindles (BJ). This is the latest application in our billet hub series. This hub utilises stock T1 bearings and seals. Due to the caliper design, the spindles require clearancing. Billet dust caps are included and are machined for a square speedometer drive.
The kit includes two billet hubs, two caliper brackets, machining to customer supplied spindles and all required hardware.
$850
Technical Specifications:
| Disk | 350mmx34mm (Porsche 955) |
| Caliper | Fixed, 6-piston axial mount Brembo |
| Hub | Billet |
| Spindle | CB Disk BJ |
| Offset change (side) | +33.8mm/side |
| Bolt pattern | 5-130mm |
| Part Number |
Posted in Type 1/3 | Comments Off on 955 Brakes on Dropped BJ spindle
993 Brakes on Type3
Wednesday, May 11th, 2011
This kit adapts 993 brakes to a T1 (BJ, SB) or T3 spindle (shown). This kit adapts 993 brake components to stock height disk spindles. (Dropped spindles can also be used). The hubs are modified to take T1 bearings. Grease seal adaptors allow the use of stock beetle grease seals.
The spindles require machining to mount the caliper. The spindle will no longer be able to take a stock T1 caliper.
The kit included machining of YOUR of your hubs to take beetle bearings, fabrication of two caliper brackets, maching of YOUR spindles to accept the caliper bracket, installed German bearings/seals and all required fasteners.+7mm offset increase per side.
$c640
Posted in Type 1/3 | Comments Off on 993 Brakes on Type3
24mm/27mm Wrench
Wednesday, May 11th, 2011
VdubEngineering (www.vdubengineering.com) is proud to introduce this 24/27mm wrench that fulfills the need for a slim-line (6.22mm thick) wrench for late model VW (24mm for balljoint BJ Beetle/T3) or early bus/bug (27mm for 63-67 Bus or Link Pin Bug -65) front spindle nuts. One end is 24mm and the other end is 27mm. Designed by certified mechanical engineer, CAD drafted and precision laser cut for exact fit. All our parts are designed, inspected and tested IN HOUSE (Mississauga, Ontario, Canada), to keep quality control on a tight leash.
$c19.95
Posted in Brake Parts & Kits | Comments Off on 24mm/27mm Wrench
Brake pushrod – Oval beetle
Wednesday, May 11th, 2011
Brake pedal push rods for oval bugs. Allows the use of 944 master cylinder without any mods.
$C25ea.
Posted in Brake Parts & Kits | Comments Off on Brake pushrod – Oval beetle
944 Turbo on BJ dropped spindle
Wednesday, May 11th, 2011
This kit adapts 86 or 87-89 944T brake components to the CB dropped disk BJ spindle. The hubs are modified to take T1 bearings and stock beetle grease seals. The spindles require a significant amount of machining to mount the caliper. The spindle will no longer be able to take stock T1 components. Offset increase of the brakes is 13mm per side.
The kit included machining of YOUR of your hubs to take beetle bearings, fabrication of two caliper brackets, machining of YOUR spindles to accept the caliper bracket, installed German bearings and all required fasteners.
$c540
Posted in New, Type 1/3 | Comments Off on 944 Turbo on BJ dropped spindle
-
You are currently browsing the vDub Engineering blog archives for May, 2011.
Pages
Archives
Categories
- Best (1)
- New (6)
- Products (41)
- Brake Parent (32)
- Brake Parts & Kits (4)
- Porsche (4)
- Type 1/3 (13)
- Type 2 (11)
- Services (1)
- Suspension/Engine (6)
- vDub Gear (1)
- Brake Parent (32)
- Technical (5)
- Uncategorized (8)